DE NEEF® Denepox Rapid Gel is a non-sagging, rapid curing, 100% solids, two component, fast setting epoxy gel used for patching, surface sealing, and bonding substrates. DE NEEF® Denepox Rapid Gel is a thixotropic gel with 1% elongation that works well for port adhesion and surface patching when injecting epoxies, especially if done the same day. DE NEEF® Denepox Rapid Gel is moisture insensitive so it can be applied in damp or even wet conditions. This product meets ASTM C-881, Type: IV, Grade: 3, Class: A, B and C.
- Fast setting
- Low odor – no mercaptans
- Moisture insensitive
- No shrinkage
- High strength
- 100% solids
- Easy to apply
- Tenacious adhesion
- Surface patching
- Surface sealing
- Bonding substrates
Surface of application should be clean and sound. The surface must be free of dust, oil, grease, laitance, curing compounds, or any other contaminants. It may be dry, damp, or wet, but must be free of standing water. The very best results are obtained on dry concrete. Do NOT apply on surfaces which have been sealed with a permanent type of form oil, curing compound or release agent. Remove these substances before application. The surface temperature must be 40°F and rising. Precondition the materials to between 65°F – 85°F before using. Refer to DE NEEF® Surface Preparation Guidelines for more details.
Mixing Procedure: Stir each component separately. Mix 1 part A with 1 part B by volume into a clean mixing container. Mix the epoxy with a slow speed drill with a mixing paddle attachment. Carefully scrape the sides and bottom of the pail during mixing with a paint stirring stick. Blend until a consistent color is observed. Mix only the amount of materials that can be used within the pot life. Please note: Large batches of epoxy will cure much faster than small batches. Mixed epoxy will cure much faster in hot weather than in cold weather.
Due to its very short pot life, DE NEEF® Denepox Rapid Gel must be placed quickly. Best when applied in less than 25 mil thickness. For thicker applications use several thin layers. Allow cooling time before doing additional layers because of exothermic reaction.
Packaging & Handling
2 gallon units; 10.5 oz side by side cartridges
Shelf Life: A minimum of 1 year in original, unopened container
Storage: Store in a dry area, between 40°F and 95°F. Protect from sunlight.
Application at ambient temperature below 40°F is not recommended. Exposure to temperatures exceeding 150°F for prolonged periods is not recommended.
Health and Safety
WARNINGS: KEEP CONTAINER CLOSED WHEN NOT IN USE. KEEP OUT OF REACH OF CHILDREN. NOT FOR INTERNAL CONSUMPTION. FOR PROFESSIONAL USE ONLY BY A QUALIFIED TECHNICIAN.
Component A - IRRITANT - Prolonged skin or eye contact may cause sensitization and irritation.
Component B - CORROSIVE - Contact with skin or eyes may cause severe burns.
- Skin Contact: Wash thoroughly with soap and water.
- Eye Contact: Flush immediately with clean water and contact a physician.
- Respiratory Problems: Remove affected person to fresh air immediately and contact a physician.
- Hygiene: Wash hands immediately after use. Wash clothing before reuse.
- Spills: Collect with absorbent material. Remaining material may be removed with a suitable solvent.
- Disposal: Dispose of in accordance with local, stale and federal regulations.
Always use protective clothing, gloves and goggles consistent with OSHA regulations during use. Avoid eye and skin contact. Do not ingest. Refer to Safety Data Sheet for detailed safety precautions.
In the event of an EMERGENCY call: CHEMTREC 800-424-9300.
|DE NEEF® DENEPOX RAPID GEL|
|Property||Part A||Part B|
|Weight per gallon||13.97 lb||12.71 lb|
|Shelf Life||1 year||1 year|
|Property||Mixed A and B||Test|
|Mix Ratio by Volume||1:1 (A:B)||N/A|
|Pot Life (3 oz. at 77° F)||4-5 min.||N/A|
|Hardness (Shore D - 77° F)||75||D-2240|
|Gel Time (5 mil - 77° F)||15-20 min.||N/A|
|Tensile Strength||6,000 psi||D-638|
|Flexural Strength||4,000 psi||D-790|
|Compressive Strength||10,880 psi||D-695|
|Bond Strength (48 hrs.)||2,934 psi||C-882|
|Water Absorption (24 hrs||0.35%||N/A|
Note: The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.
gcpat.com | North America Customer Service: 1 877-4AD-MIX1 (1 877-423-6491)
We hope the information here will be helpful. It is based on data and knowledge considered to be true and accurate, and is offered for consideration, investigation and verification by the user, but we do not warrant the results to be obtained. Please read all statements, recommendations, and suggestions in conjunction with our conditions of sale, which apply to all goods supplied by us. No statement, recommendation, or suggestion is intended for any use that would infringe any patent, copyright, or other third party right.
DE NEEF is a trademark, which may be registered in the United States and/or other countries, of GCP Applied Technologies Inc. This trademark list has been compiled using available published information as of the publication date and may not accurately reflect current trademark ownership or status.
© Copyright 2018 GCP Applied Technologies Inc. All rights reserved.
GCP Applied Technologies Inc., 62 Whittemore Avenue, Cambridge, MA 02140 USA.
In Canada, GCP Canada, Inc., 294 Clements Road, West, Ajax, Ontario, Canada L1S 3C6.
This document is only current as of the last updated date stated below and is valid only for use in the United States. It is important that you always refer to the currently available information at the URL below to provide the most current product information at the time of use. Additional literature such as Contractor Manuals, Technical Bulletins, Detail Drawings and detailing recommendations and other relevant documents are also available on www.gcpat.com. Information found on other websites must not be relied upon, as they may not be up-to-date or applicable to the conditions in your location and we do not accept any responsibility for their content. If there are any conflicts or if you need more information, please contact GCP Customer Service.
Last Updated: 2018-11-29